[คลังสินค้าใส] เครื่องดูดลูกปืน มูเล่ย์ ไฮดรอลิก เหล็กดูดสามขาไฮดรอลิค 5T เกียร์ไฮดรอลิปั๊มน้ํามันท่อ 3 ขากรรไกรเครื่องวาดภาพ

---------- ยินดีกับร้าน Ryo Tools ----------

☺เครื่องมือฮาร์ดแวร์คุณภาพสูง
☺โปรโมชั่นต่างๆ
☺ไปที่ร้านเพื่อรับคูปอง
☺สนับสนุนเก็บเงินปลายทาง
☺ขอบคุณที่ให้ความสนใจกับทางร้าน

Features:
Made of forged steel this hydraulic puller is very strong and durable with good bearing capacity and long service life.
It
is equipped with 3 pulling claws which can be adjusted from high to
low and can be pulled with two or three legs according to different
needs.
There is a handle that can be opened which can be operated with very little operation and get great pulling force.
The safety overflow valve control switch on the pump body is ready to avoid oil pressure overload.
The
hydraulic puller adopts the design of 360-degree pump head which is
easy to operate and easy to use. After rotation it can quickly contact
the working center according to the distance between the puller and the
position center.
Suitable for traction hubs flanges gears and bearings with a maximum carrying capacity of 10 tons.
 

Specification:
Material: carbon steel + cast iron
Ares travel: 2 inches (50 mm)
Maximum capacity: 5T
Minimum/maximum range: 0-5.51(0-140mm)   
Minimum/maximum transmission: 4-  7.87(100-200mm)
Weight: Approx.7100g/250.4oz
 
Usage and precautions:
1. Please put the open handle end into the puller shaft and tighten the shaft according to the clock direction.
2. Adjust the jaws to maintain proper distance and Angle from the pulling position.
3. Rotate the handle to make the piston shaft move and promote the power of the jaw to disengage the object.
4.
The maximum stroke of this hydraulic puller is 50mm please pay
attention when using it so you may need to try many times when the
object is still in the position that meets the requirements of the
stroke.
5. To return the piston starting rod simply use the grooved end of the handle and rotate the return stem counterclockwise.
6.Dont overload.
7. Use (GB443-84) oil N15 at -5℃~ 45℃ the spindle oil (GB442-64) synthesis in-20℃~-5℃.
8. The machine uses oil as the medium so the oil and the machine must be kept together.
9.
With a new setting or a long setting the hydraulic puller can be
loaded 2 to 3 times to eliminate the air cavity since there is a large
amount of air in the cylinder and the rod may have a small sudden jump
when starting. Although the gear puller is out of use for a long time
you should reciprocate the gear puller 2-3 times a month.
 

Package List:
1 x Hydraulic Puller
1 x Handle
1 x 2/3 Leg Puller Yoke
3 x Jaws
6 x Nuts and Bolts
6 x Link Plates
1 x Nose Adapter  
1 x Carrying Case

Note:
Please note that the new type and old type of this product will be sent randomly and make sure you will not mind before ordering.

#5THydraulicGearPullerPump #HydraulicGearPullerPump #HydraulicPuller #HydraulicGearPuller #5tHydraulicGearPuller